Three close views show the metal finish, the overlapping rings, and the joint where the stem meets the bar
01A curved ring fills the frame, its face marked by fine brush lines that follow the arc. A bright warm line runs along the inner rim02Two rings overlap around a flat horizontal bar, both edged with a soft inner glow. The larger ring crosses the smaller one where the bar passes through03A vertical rod meets the horizontal bar at a small rounded joint. A large ring curves in front of the bar, its inner edge lit, with another ring partly visible behind
Ring Pendant Light
Overlapping Rings
Soft Downward Light
Two brass rings, one smaller and one larger, overlap on a long horizontal brass bar. The bar hangs from a matching canopy on thin wires, so the rings float at eye level or just above. When the light is on, it pools downward and spreads soft, while the rings read as clean geometry
Highlights
Brass Rings, Soft Pool
Overlapping rings on a matte brass bar send a soft pool of light downward
01
Brass and Silica Gel
The pendant is made of brass and silica gel, with brass forming the rings and the long horizontal bar
02
Matte Brass Finish
A warm matte brass finish catches light without gloss. A clear protective coat resists fingerprints and oxidation indoors
03
Three-Color LED
A built-in integrated LED changes among warm white, neutral white, and cool white. A button switch controls it, and the light is not dimmable
04
One Clear Span
The fixture is about 28 inches wide and 12 inches tall, with rings about 10 inches in diameter
Specifications
Size and light
Length
Size: 35.4″ (90 cm)
Height
Size: 59″ (150 cm)
Ring diameter
Approx. 10″ (25 cm)
Wire length
59″ (150 cm), extendable upon request
Source
Built-in integrated LED
Color
Warm white, neutral white, cool white
Voltage
AC 110–240V
Control
Button switch (not dimmable)
Material
Brass, silica gel
Finish
Matte brass; silica gel white
Brass · Warm LightL 90cm x H 150cm / L 35.4″ x H 59″
HOZO Installationsanleitung
Planen Sie Ihre Beleuchtung.
Raumweise Startwerte für Leuchtengröße, Montagehöhe, Abstand und Durchgangshöhe. Tippen Sie ein Kapitel an.
01
Esstisch
Größe und Mitte vom Tisch aus festlegen, dann die Sicht von jedem Sitz prüfen.
So messen
Tischlänge und -breite messen. Bei runden Tischen den Durchmesser nehmen.
Startbereich
Runde Leuchten: etwa 1/2 bis 2/3 der Tischbreite. Längliche Leuchten: 1/2 bis 2/3 der Tischlänge.
Platzierung
Die Leuchte über dem Tisch zentrieren, nicht zwingend über dem Raum.
Abstand
76–91 cm über der Tischplatte beginnen.
Bei langen Tischen wirken zwei kleinere Pendel oft natürlicher als eine übergroße Leuchte.
Vor dem Bohren
Eine Papierschablone an die Decke kleben und vom Türrahmen sowie sitzend prüfen.
MessenPlatte bis Unterkante
Hängehöhe76–91 cm
AusrichtenMitte des Tisches
02
Kücheninsel
Die nutzbare Insel messen und die Pendel auf der Mittellinie halten.
So messen
Nutzbare Länge und Breite der Insel messen.
Startbereich
Eine Linienleuchte: 1/2 bis 2/3 der Insel-Länge. Mehrere Pendel: erst den Durchmesser, dann die Anzahl wählen.
Platzierung
Pendelmitten gleichmäßig auf der Insel-Mittellinie.
Abstand
76–91 cm über der Arbeitsplatte. Äußere Pendel nicht an den Inselenden.
Die komplette Reihe mocken, nicht nur ein Pendel.
Vor dem Bohren
Drei Papierkreise über der Insel zeigen Abstandsprobleme schneller als ein einzelnes Muster.
MessenPlatte bis Unterkante
Hängehöhe76–91 cm
AusrichtenGleiche Mitten
03
Raummitte
Länge plus Breite ergibt den Startdurchmesser. Deckenhöhe und visuelle Schwere machen die Entscheidung fertig.
So messen
Raumlänge und -breite in Metern plus fertige Deckenhöhe.
Startbereich
Länge + Breite (m) × 8,3 ergibt einen üblichen Startdurchmesser in cm. Beispiel: 3,7 + 3,0 → ca. 56 cm.
Platzierung
Die architektonische Mitte nur nutzen, wenn sie vom Eingang und vom Möbelplan her Sinn ergibt.
Abstand
Mindestens 2,10 m lichte Höhe unter dem tiefsten Punkt im Laufbereich.